How to Wall Mount Amazon Ember Artline TV
Use the included wall mounting hardware to mount your device on your wall.
Table of Contents
Overview
- DO NOT mount on drywall or plaster board without stud support.
- Failure to follow instructions could cause serious injury and/or TV damage.
- Setup requires at least two people.
- Wall mount is designed for use only with the included TV.
Before getting started, you need:
- The included wall mounting template, along with the bolts, screws, and anchors.
- An electric drill with a 1/8” (or 3 mm) drill bit for stud mounting, 3/16” (or 5 mm) drill bit for magnet plate installation, or 5/16" drill bit (or 7 mm) for brick/concrete mounting, and a Phillips #2 driver bit
- A hammer
- A level or level app
- Stud finder
Safety Guidelines
- DO NOT Mount on drywall or plaster board without stud support.
- Failure to follow instructions could cause serious injury and/or TV damage.
- If stud spacing is not standard or if studs are not present, contact a professional for installation to prevent potential mount failure.
- If you are installing the wall mount on a drywall without proper stud spacing, we recommend that you contact a professional to complete the installation.
- Use TV dimensions to plan the placement of the mount.
- Consider the height of everyone using the device. We recommend placing the TV at eye level.
- Find a mount location away from water or moisture.
- Don’t drill holes over electrical wiring or piping.
- Before mounting, unplug the device from electric outlets.
- If you’re installing the mount on a brick wall, locate an area free of cracks.
Prepare TV for Wall Mount
Video guide to set up your device
- Carefully unpack the TV and all included accessories from the box.
Note: Make sure that you remove all the parts and accessories before disposing of the box.
- Remove the plastic bag and lay the TV screen-side down to access the recess cover.
- Remove the recess cover and install the 2 mount bolts using a Phillips screwdriver as shown below. To prevent stripping the bolt holes, do not use an electric drill.
Install the Mount
- DO NOT Mount on drywall or plaster board without stud support.
- Failure to follow instructions could cause serious injury and/or TV damage.
- If stud spacing is not standard or if studs are not present, contact a professional for installation to prevent potential mount failure.
Use a stud finder to locate 2 studs. Use a level or level app and mark the center of each stud with a pencil. If installing on brick/concrete, locate an area free of cracks.
2. Place the mount template on the wall and attach it with a double-sided tape. Use the template to see approximately where the TV will be mounted on the wall.
3. Place the mount against the wall and mark at least 4 screw holes. Use a level or level app. For studs, line up the screw holes with the center of each stud. For brick/concrete, line up the screw holes with bricks on each side of the mount, avoiding mortar between bricks.
4. Drill the pilot holes using an electric drill.
- If installing on studs, use a 1/8” drill bit.
Warning: For drywall without stud support, contact a professional to complete installation.
- If installing on a brick/concrete wall, use a 5/16” drill bit. After drilling, insert the mount anchors into the holes and secure them using a hammer.
- After drilling, insert the mount anchors into the holes and secure them using a hammer.
5. Attach the mount to the wall using the mount screws, an electric drill, and a Philips #2 bit.
- If installing on studs, install the screws through the mount and into the studs. DO NOT use long plastic anchors with screws for studs mounting.
- If installing on brick/concrete, install the screws through the mount and into the anchors.
6. Mark the locations for the 4 magnet plates on the wall and remove the template.
7. Drill the pilot holes using a 3/16” drill bit and an electric drill.
8. Install the 4 magnet plate anchors using a hammer.
9. Install the magnet plates to the anchors using the magnet screws and an electric drill.
Attach the TV to the Mount
- At least two people needed for lifting and attaching TV to the mount.
- DO NOT press against the screen during installation.
1. Gently release the bolt latches and fully extend the TV bracket away from the wall.
2. Place four alignment stickers above the mount bolts and bolt latches. Fold the stickers up for visibility during installation.
3. Attach the TV to the TV bracket by hanging the mount bolts on to the mount hooks. Use the alignment stickers for guidance.
4. Close the bolt latches to secure the mount bolts into mount hooks.
5. Gently push the TV to the wall and connect the magnets with the magnet plates on the wall.
Video Guide to Wall Mount Installation
